Vehicles
Sections
152 not categorized PORSCHE 924 WIL VICan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: CAYENNE 2007-10 (includes uncategorized and accessory items) 91151192302EQ1 This gasket sits on the inside of the hood in the front trunk. It tends to get nicked and cut and will degrade with time. It is essential to keep moisture out of the trunk and should be replaced at the first signs of damage. This is a high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$136.40
Make a selection 964561005016HA This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames, like the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German ...(choose a part on the right to read more)
$2,201.10
Make a selection 96560612601EQ Oxygen or lambda sensors are critical to your engines health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Be sure to check the "fits these models" tab to make sure that this will work for your needs. Sold individually. 1 necessary per car.
$111.10
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$196.90
Make a selection 96437502301ATK Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our mount is remanufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.
$178.20
Make a selection 92834102733ATK By ordering this part number you get after previous sending in your wishbone overhauled with new silent blocs back. Should it not be repairable, we will inform you immediately.
$342.10
Make a selection 930602015AX2ATK Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt (part # FVD 602 964 00) and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.
$504.11
Make a selection 96453109500EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 96434101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 90173101020 This is a new production of the rear view mirrors, where it does't have heaving crimping on the corner of the metal to the mirror edge, great quality manufactured product. This will fit your Porsche 911 & 912 from ' 65 - ' 67.
$49.99
Make a selection 901602702AXATK The cdi or hkz as it is known in Germany, is the high-voltage condenser ignition control unit. Aging cdi / hkz units lead to deterioration of performance with time. A failing unit's symptoms include a fluctuating tach, stalling, loss of power to the ignition coil and no start situations, leaving you stranded. Send us your original cdi / hkz and German technicians with many years of experience will completely remanufacture it to new specifications. This is not a repaired unit like many of our competition offer, this is a completely remanufactured unit using new upgraded components. The remanufacturing process includes: disassembly inspection and cleaning complete diagnosis (including oscillogram) on a test benc...(choose a part on the right to read more)
$768.90
Make a selection 96434101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 017 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 93010505304 High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. For installation on the left-hand side, you will need 1 qty. Spacer, part # 93010551300 and 1 qty. Chain wheel support, part # 93010550900. For installation on the right-hand side, you will need 1 qty. Spacer, part # 93010551300 and 1 qty. Chain wheel support, part # 93010551000 sold individually. Left or right-side fitment. 2 necessary per car.
From $589.60
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$322.21
Make a selection 964347009BXATK This steering rack is a remanufactured part with a core, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection and testing for structural integrity. We then disassemble and bead blast to remove corrosion. Internals are micro-finished to OEM specifications. Sealing surfaces are carefully checked and restored prior to installing new premium seals and o-rings. Each unit is then carefully tested for full functional...(choose a part on the right to read more)
$1,633.50
Make a selection
From $106.00
Make a selection
From $106.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |